A Aiwa BZG-2 free download

File name A Aiwa.pdf

BZG-2 English SERVICE MANUAL CD MECHANISM BASIC CD MECHANISM :KSM2131FAM TYPE ZD4NC YZD4NC ZD4N YZD4NCC BASIC CD MECHANISM KSM-2131FAM KSM-2131FAM KSM-2131FAM KSM-2131FAM S/M Code No. 09-00C-353-2N2 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION. BE SURE TO OBSERVE FROM A DISTANCE OF MORE THAN 30cm FROM THE SURFACE OF THE OBJECTIVE LENS ON THE OPTICAL PICK-UP BLOCK. Caution: Invisible laser radiation when open and interlocks defeated avoid exposure to beam. Advarsel:Usynling laserstеling ved еbning, nеr sikkerhedsafbrydere er ude af funktion. Undgе udsжttelse for strеling. ATTENTION L'utilisation de commandes, rйglages ou procйdures autres que ceux spйcifiйs peut entraоner une dangereuse exposition aux radiations. ADVARSEL! Usynlig laserstеling ved еbning, nеr sikkerhedsafbrydereer ude af funktion. Undgе udsжttelse for strеling. This Compact Disc player is classified as a CLASS 1 LASER product. The CLASS 1 LASER PRODUCT label is located on the rear exterior. VAROITUS! Laiteen Kдyttдminen muulla kuin tдssд kдyttцohjeessa mainitulla tavalla saattaa altistaa kдyt-tдjдn turvallisuusluokan 1 ylittдvдlle nдkymдttцmдlle lasersдteilylle. VARNING! Om apparaten anvдnds pе annat sдtt дn vad som specificeras i denna bruksanvising, kan anvдndaren utsдttas fцr osynling laserstrеlning, som цverskrider grдnsen fцr laserklass 1. CLASS 1 KLASSE 1 LUOKAN 1 KLASS 1 LASER PRODUCT LASER PRODUKT LASER LAITE LASER APPARAT -2- Precaution to replace Optical block (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure. -3- How to Adjust the Rotating Phase of the Gear, Main Cam 1) Push down the hooking catch of the CHAS. MECH, and remove the TRAY. 2) Align the arrow mark of the Gear, Main Cam with the black round mark of the CHAS, MECHA as shown below. 3) Confirm that the Slide, Mech Cam is located in the right position, then insert the TRAY gently. Caution: If the rotating phase of the Gear, Main Cam is incorrectly adjusted, the chucking operation and tray movement will have malfunction. Align the arrow 2 mark with the black round · mark. -4- ELECTRICAL MAIN PARTS LIST-1/2 REF. NO IC PART NO. KANRI NO. DESCRIPTION REF. NO C135 C136 C137 C138 C160 C161 C203 C204 C205 C208 C212 C213 C214 C301 C302 C303 C304 C305 C401 C402 C403 C404 C405 CN1 CN202 CN301 CN401 CNA203 L101 M201 R104 R106 S401 S402 W1 W2 X101 T-T C.B C401 CN401 M401 PS401 MOTOR C.B M2 PIN3 SW1 87-A21-821-030 87-A21-414